Re: [BaadAssGremlins] Which Cylinder Heads ????
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [BaadAssGremlins] Which Cylinder Heads ????





Or if you REALLY want to boost some H.P go with a set of Herman Lewis alum heads.
Bart
 
In a message dated 4/7/2010 7:50:24 A.M. Eastern Daylight Time, martin-davis@xxxxxxxxxxxxx writes:
 

Ed,
 I assume since you mention the edelbrock heads, money isnt the real issue. That being said heres what I think and why.
 I would not even think about using anything but an aluminum head.  Why? The aluminum Head has a more modern design, Better shaped combustion chamber, better runner design, better cooling effect of the aluminum, less detonation better complete fuel burn. The cost is about 2 times the cost of rebuilding the iron heads but the benifit is 4 times better. Also later when you decide you would like more power, you can send the heads out for a port job and get quite a bit more outta your engine.
 I hope I have been clear....It doesnt matter which heads you go with, you have to think what are your future goals?
 Davis


From: "mrmopar00@yahoo.com" <mrmopar00@yahoo.com>
To: BaadAssGremlins@yahoogroups.com
Sent: Tue, April 6, 2010 4:07:54 PM
Subject: Re: [BaadAssGremlins] Which Cylinder Heads ????

 

I would look an Eddy or indy SR head. Is it worth it to you to invest $ in the old iron head?
Olly

Sent from my BlackBerry device on the Rogers Wireless Network


From: Ed Veneck <edveneck@yahoo. com>
Date: Tue, 6 Apr 2010 16:02:59 -0700 (PDT)
To: <BaadAssGremlins@ yahoogroups. com>
Subject: Re: [BaadAssGremlins] Which Cylinder Heads ????

 

Yes, the first set is the worst, needing new valves, seats, guides and springs.  The set with the bridged rockets just needs a valve job on it.

--- On Tue, 4/6/10, mrmopar00@yahoo. com <mrmopar00@yahoo. com> wrote:

From: mrmopar00@yahoo. com <mrmopar00@yahoo. com>
Subject: Re: [BaadAssGremlins] Which Cylinder Heads ????
To: BaadAssGremlins@ yahoogroups. com
Date: Tuesday, April 6, 2010, 5:56 PM

 
Do u have to put $ in the iron heads?
Olly


Sent from my BlackBerry device on the Rogers Wireless Network

From: Ed Veneck <edveneck@yahoo. com>
Date: Tue, 6 Apr 2010 15:36:59 -0700 (PDT)
To: Gremlin list<BaadAssGremlins@ yahoogroups. com>
Subject: [BaadAssGremlins] Which Cylinder Heads ????

 
I'm building a mild 401 street engine for my Gremlin, and I two heads to choose from.  the first set is casting number 3216090 - from a 360/401 with 58cc chamber & stud rockets.  The second is casting number 3231475 - from a 360/401 with 58cc chamber & bridged rockets.  Which would be the better set of heads?  I do plan on running a set of Roller Rocker Arms.  Or should I just buy a set of Edelbrock Aluminum Heads.
 
Ed




__._,_.___


Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___


Home Back to the Home of the AMC Gremlin 


This site contains affiliate links for which we may be compensated