Re: [AMC-list] OK, I now admit it, the T-96 sucks
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [AMC-list] OK, I now admit it, the T-96 sucks



Missed a part.
The T4 has a wide gear spread.
4-1 first and like about 2.40-1 second. I forget the exact number. No O.D.
I have one here, needs a speedo drive gear on the output, It's been available to Tom for $20 for a long time no.
Not sure you can get the speedo drive gear anyway though, need someone with a parts gear to look see.
I need the one that was in it for mine.

Mark Price
Morgantown, WV 26508
1969 AMC Rambler, 4.0L, EFI, T-5
2004 Grand Cherokee Laredo, 4.7L, Quadratrac II
"I realize that death is inevitable.
I just don't want to be around when it happens!"

----- Original Message -----
From: "Frank Swygert" <farna@xxxxxxx>
To: amc-list@xxxxxxxxxxxx
Sent: Sunday, April 19, 2009 12:56:18 PM GMT -05:00 US/Canada Eastern
Subject: Re: [AMC-list] OK, I now admit it, the T-96 sucks

Yeah, anything more than "granny driving" and you find that trans lacking. I do know that the top two bolts on an SR-4 (T-4) will match the top ones on the T-96 bell, but the bearing retainer is bigger on the T-4/T-5. You have a mill, so can fix that "problem". I thought about using a piece of 1/8" plate between the trans and bell with 3/4"-1" flanges bent on each side towards the trans to stiffen it. Bolt the plate to the bell using the bottom two trans bolt holes. Might have to grind the front side of the trans or thin the bolt heads for clearance, not sure. Use nuts and bolts for the bottom of the trans. Since you would be keeping the bell mounts I don't see where any more reinforcement would be needed, but a pair or straps could be mounted on the bottom trans bolts and extend to the back of the engine. The trans should just hang there like the T-96, which is heavier (at least with OD). 

By the way, T-4s were used in early 84 four cylinder XJ Jeeps, but I don't think there was a 2WD version until 85 or 86. Later 83-91 four cylinder models used an Aisin Warner AX4 or AX5. One of those may work also. 

---------
Date: Sat, 18 Apr 2009 16:25:43 -0700
From: tom jennings <tomj@xxxxxxx>

OK, you can't say I didn't give it a chance. It's still working fine, or, as
fine as a T-96 can. It is by far the slowest thing in the car. It's really
holding it back. It's just so damn slow to shift! There's nothing wrong with
the synchros or the oil I used, as far as I know. I checked all the
clearances and it was all new parts. It just shifts slooooow! If you move
too fast it get chunky. (The spec for maximum synchro stack clearance is
.094" -- a tenth-inch oil film is all that drags the gear up to shaft
speed.)

And a four speed would really help get some work out of this motor. I'm
having a blast driving this car, still, and it's very nimble in traffic,
something that comes as a surprise. A 100% perfect suspension, good fat
tires and oversized brakes makes all the difference.

So back I go to finding a cheap T-4, but I wish there was a side-shifted
trans that would fit. And thoguh I hate to give up Twin Stick, I'll probably
do it (and save all the parts!).

-- 
Frank Swygert
Publisher, "American Motors Cars" 
Magazine (AMC)
For all AMC enthusiasts
http://farna.home.att.net/AMC.html
(free download available!)


_______________________________________________
AMC-list mailing list
AMC-list@xxxxxxxxxxxx
http://list.amc-list.com/listinfo.cgi/amc-list-amc-list.com
_______________________________________________
AMC-list mailing list
AMC-list@xxxxxxxxxxxx
http://list.amc-list.com/listinfo.cgi/amc-list-amc-list.com


Home Back to the Home of the AMC Gremlin 


This site contains affiliate links for which we may be compensated