RE: More T-5 Nuggets
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: More T-5 Nuggets



Mark, It NOT the gears that makes a World Class T-5, I also think you mint 3.95:1 for NWC T-5s on your comments below. NWC T-5 counter shafts used thrust washers and straight roller thrust bearings for end play. For reduced noise and improved durability, WC T-5s replace them with tapered roller bearings and shimming packages. Older T-5s versions can't be updated to WC T-5s.

Also the speed (main Shaft) gears on NWC T-5s rode directly on the mainshaft journal, with metal-to-metal contact prevented solely by transmission lubricant delivered via grooves machined into the main shaft. WC T-5s have needle bearings under the speed gears for improved HIGH-SPEED performance and reduced shift effort.

NWC T-5s used "traditional" solid brass synchronized blocker rings, WC T-5s introduced 3-4 synchros made from powered-steel blocker rings, and lined them with rust-colored organic friction material. 1992 Ford T-5s use and even more durable black organic lining. The "black" blocker service parts were available from Borg-Warner distributors under PN 1352-410-003. Solid one-piece brass synchros were used in the 1-2 position as well, the WC T-5 versions are upgraded to the three-piece, double-cone synchro design, this greatly increases the available friction surface (grabbing) area. All V-8 Mustangs went to the WC T-5s in 1985 and GM went to the WC T-5 in 1988 for their V-8s. My books state that all manufactures used the WC T-5s in all V-8s after 1988, the NWC T-5s in four- and six-cylinders.

Car Craft stated in may 1992 that the Ford WC T-5s low-gear-ratios were 3.35:1 and GM used only 2.95:1 tyranny's. The GM case fits GM and Isuzu bellhousings. The Ford pattern fits the AMC, Jeep, and Nissan. NWC and WC T-5s use different cases, so there are four different main cases (two for GM and two for FORD) The easily way to determine GM from Ford other than the bolt up pattern is where the speedometer cable is and also by the shifter mounting locations. On GM the speedometer cable is at the bottom of the trans under the tail shaft gear, on the ford its in the middle of the tail shaft housing ridding on top of the tail shaft gear. On the GM the shifter block stops about 2" from the back of the trans, the Ford stops about 4 to 5" from the end of the trans. GM T-5s have a 26-Spline input shaft and Ford has a 10-Spline. Also looking at the front of the trans a small single-colored front countershaft bearing retainer stamped "Torrington" at the top will tell you its a NWC. A large two-color (gray with outer ring) bearing marked "timkin" identifies the WC T-5s. This is all taken from 1992 information I have on pre 1992 trans, any thing after can change..........

WC T-5s with the 2.95:1 and 3.35:1 can be identified by placing them in 1st gear and turning the front shaft three complete revolutions, this should cause the mainshaft to rotate about one turn. On NWC 3.97:1 non-V8 can be identified by placing them in 1st gear and turning the front shaft four complete revolutions, this should cause the mainshaft to rotate about one turn

All WC T-5s equipped with 2.95:1 and 3.35:1 low gears carries a factory torque rating of approximately 305 lbs-ft based on 100,000 mile durability cycle and typical design overkill. All the information I have on the WC T-5s also state that you only use Dexron II automatic Fluid in them...........There was a Mod made in 1985 to fix the Third gear problems on the synchros.

I can't weight to see how many people jump on this..........

Joe W.



Date: Thu,  3 Mar 2005 21:01:05 -0500
Message-Id: <200503032101.AA68681912@xxxxxxxxxxxxxxx>
From: <mail@xxxxxxxxxxxx>
To: <mail@xxxxxxxxxxxx>
Subject: More T-5 Nuggets

Well, I've dug up some more factoids on the T-5.
One I did not know the early non Worldclass V-8 transmissions all have 2.95 first gear, Chevy and Ford. They are rated at 265 lbs torque for 100,000 miles. Everyone says, get a World Class,Well, This is true only if you get a 90 up one! Otherwise the Torque rating is still 265 ft lb up to 90. The only thing the World class transmssions gained was supposed smoother shifting and some durability, except if you read on them you find out that 87-89 World class T-5's love to loose the coating off their synchros and strip teeth from third gear. Hmm world Class? I wonder.
Anyway, What I can find points me to the fact that to build the tranny I want for my American I need to get my hands on an 83-84 Mustang V-8 T-5 or 82-87 Camaro-Firbird V-8 T5 for the gearsets.
If anyone runs across such a beast that I can use for the core to build let me know!
Also still looking for an AMC T-5 to rob the tailhousing, shifter and output shaft from.





Mark Price
mpriceATwestco.net
Morgantown, WV
69 AMC rambler, 4.0L, EFI, 5 speed
65 Ambassador Conv, 327 AUTO, Basketcase
01 S-10 CREWCRAP 4X4








Home Back to the Home of the AMC Gremlin 


This site contains affiliate links for which we may be compensated